Industrial wireless remote control DH01R-4W-26K

Description

model：DH01R-4W-26K adapter equipment：Various industrial equipment

Remark：You can choose one of three antennas，Default standard suction cup antenna

Remark：
① DH01R series，If the suffix contains T, it means with emergency stop output.；Without T means without emergency stop output。
②If there is no analog output，No need to remark 0W or 0R；Analog quantities W1, W2, W3, and W4 default to 0-10V analog voltage output；At the same time, W1 and W2 can expand 2 isolated digital potentiometer outputs.，Range 0-5K ohms，1/2watt；resolution：20ohm。The two digital potentials can be used to control the welding current and welding voltage of the welding machine.。If the digital potentiometer output is required，User notes required。
④Analog input，Range from 1 to 2，Indicates that there are 1 to 2 analog inputs (maximum 2 channels)；When there is an analog input，Need to note the voltage range of the analog input (our receiver defaults to 0-5V，Users can also note 4-20 mA or 0-10V, etc.) and the corresponding display range of the analog quantity.(such as：Displays 0-100 volts or 0-1000 amps)
These two analog quantities can be used as displays for welding current and welding voltage.。

W1 knob value：W1：0-1000(Parameter adjustable 0-9999)
W2 knob value：W2：0-5000(Parameter adjustable 0-9999)
W3 knob value：W3：0-5000(Parameter adjustable 0-9999)
W4 knob value：W4：0-5000(Parameter adjustable 0-9999)
ADC1 feedback display：0-1000(Parameter adjustable 0-5000)
ADC2 feedback display：0-1000(Parameter adjustable 0-5000)

low pressure：Remote control battery is too low，Please replace the battery

Dropped network：Wireless signal interruption，Please check receiver power supply，Power cycle，Remote control restarts

1、Remote control power on
Receiver powered on，Receiver working indicator flashes；Install two AA batteries in the remote control，Turn on the power switch，The display shows the value，Indicates successful boot。The receiver working indicator light turns to a steady state。

2、Switch and button functions
Operate any of the twist switches and buttons on the remote control，Can control the corresponding switch signal output point at the receiver end，All switch signal output points on the receiver are normally open signals by default.

3、W1-W4 speed adjustment
Rotate the knobs in W1-W4 at will，Can operate the corresponding analog output signal or potentiometer signal at the receiver end，
The analog output signal at the receiver is a 0-10V voltage signal by default，The potentiometer signal defaults to 0-5K；

4、Emergency stop function
Photograph the emergency stop button，All switching signal outputs are disconnected，Analog output disconnected；After releasing the emergency stop，All switching signals restored，Analog output recovery；
5 seconds after the remote control is turned off，All switching signal outputs are disconnected，The analog quantity remains unchanged，Remote control power on，Switch signal output automatically recovers；

5、Parameter menu (users are prohibited from modifying it without permission)
Some functions of the remote control can be adjusted through parameters，When the display screen W1=0，Press the K9-B button 3 times in a row，Then press the K9-A button 3 times in succession，Enter parameter menu；
K9-A and K9-B keys are used to turn menu pages and select parameters.；Hold K1-A，Press the K9-A/B button again，Modify parameters；
Exit parameter menu：Choose to save or not save，Then press the K1-A button to confirm the exit；
F1W1 range:The display range value of the W1 knob on the display screen，0-9999Adjustable；
F2W2 scope:The display range value of the W2 knob on the display screen，0-9999Adjustable；
F3W3 scope:The display range value of the W3 knob on the display screen，0-9999Adjustable；
F4W4 scope:The display range value of the W4 knob on the display screen，0-9999Adjustable；
F5A1 range:Display ADC1 feedback display range value，0-5000Adjustable；
F6A2 range:Display ADC2 feedback display range value，0-5000Adjustable；
Alarm current：Set the alarm value for ADC1 and ADC2 feedback display，When ADC1 and 2 exceed this value，Remote control display alarm prompt；When this value is 0，Alarm function is invalid；